Because we are also using a random number generator in the code, we read an unconnected analog pin to get a random number to seed the random number generator. The freqout function that gets called here is written out at the end of the code. 95 Bone Conductor Transducer Cytron EasyMP3 Shield Arduino library and. The setup function starts with a line of code that makes the piezospeaker beep when the KittyBot is powered up and so that you can hear if the robot resets while driving due to low batteries. 1 // include SPI, an Dapatkan Diskon 33 untuk pembelian Music Player Mp3 Shield. Once the pins have been set up, we can set up the musicPlayer object: // create shield-example object!Īdafruit_VS1053_FilePlayer musicPlayer = Adafruit_VS1053_FilePlayer(SHIELD_RESET, SHIELD_CS, SHIELD_DCS, DREQ, CARDCS) and the distance result in inches and centimeters: The PING))) sensor requires a few variables to be declared: // establish variables for duration of the ping, #define DREQ 3 // VS1053 Data request, ideally an Interrupt pin These are common pins between breakout and shield #define SHIELD_DCS 6 // VS1053 Data/command select pin (output) #define SHIELD_CS 7 // VS1053 chip select pin (output) #define SHIELD_RESET -1 // VS1053 reset pin (unused!) The next lines of code define which pins are used by the different functions and objects in the KittyBot's code: // These are the pins used for the music maker shield The two lines are used to set up two servo objects - one for each wheel: Servo servoRight #include // We will use the hardware SPI pins: CLK (13), MISO (12), MOSI (11) The fourth is a custom library for the Adafruit "Music Maker" MP3 Shield. The three are standard Arduino Libraries. The Arduino KittyBot project includes the following libraries. You can adapt it to work with different sensors, and use your own WAV files to play different sounds. If this is the case, you will need to move or remove the one being used, at least temporarily, so that the Teensy library is used by the Arduino IDE.Let's take a look at the code. Most likely you have multiple libraries installed and the Teensy SD library is being skipped/ignored. If you receive errors with Teensy 3.5 & 3.6 code regarding the parameters for SD card initialization, look for warnings regarding the SD library.If a small card is used with FAT formatting, it will not work. SD Cards (at least on Teensy 3.5 & 3.6 need to be formatted with FAT32 file system.How to use Audacity to convert mono to stereo.Online converter to strip audio from video or convert audio to MP3 or change bitrate - Goodmorning everybody, i've just bought an Adafruit Music Maker Shield and tested it with Arduino Uno using the Adafruit library's example sketch but it doesn't work I explain better: if I run the 'playerinterrupts' sketch I heard the 'tone to indicate VS1053 is working' with headphones but not anything more I tried different formats, file names and 3 different sd cards.For example in.Encode at constant 40kbps with a sample rate of 44,100 kHz.The code is written for stereo MP3 files so if you have a mono MP3 file, it will not play back using this code as is.īest practice for producing playable MP3 files This means that the MP3 files should be encoded within this range. It's getting called 44,100 to 48,000 times per second for most MP3 files. This function is called from an interrupt, so it should be short and sweet. (At least as supported as the previous version.) Some notes regarding audio file format It is expected that it will work with all other supported boards. This release was tested with the Teensy 3.5 only. (Other examples may have the same errors so use the above notes to fix other examples if needed.) Fix applied to library and the "play_from_SD.ino" example only.Included test.mp3 sample file (58.3 KB).Added/modified comments on compiler directives for Teensy boards.Added support for Teensy 3.5 - Added defined(_MK64FX512_) wherever defined(_MK66FX1M0_) was found.Fixed issues with Teensy support - The code NVIC_DisableIRQ(MP3_IRQn) applies only to the feather and metro m4 but was applied to all boards which resulted in MP3_IRQn being undefined.Uses a decent chunk of RAM at this time! UPDATE 6 October 2018 On the SAMD51 boards, TC2 is used to create the sample timer (usually 44.1khz or 48khz). This library sets up and performs native MP3 audio decoding on various Arduino-compatible platforms including Metro/Feather M4 (SAMD51 chip), teensy 3.6, teensy 3.2, and teensy 3.1.
0 Comments
Leave a Reply. |